Flipsky FSESC 75200 Pro V2.0 ESC Speed ​​Controller, 14-84V, 200A, 4-20S, Aluminum PCB

Flipsky FSESC 75200 Pro V2.0 is a high-performance electronic speed controller (ESC) based on the VESC platform, designed to control powerful brushless motors. The controller supports an operating voltage of 14–84 V and 4–20S battery systems, delivering a continuous current of up to 200 A at 50 V and a peak current of up to 400 A.

The model is built around the STM32F405 Cortex-M4 processor (clocked at 168 MHz) and supports both BLDC and FOC control modes. It is compatible with the VESC Tool for parameter configuration, while a built-in Bluetooth module enables wireless programming and real-time data monitoring.

An aluminum PCB facilitates efficient heat dissipation during high-load operation. Built-in protections guard against overcurrent, undervoltage, overvoltage, and overheating of both the MOSFETs and the motor.

The controller supports HALL, ABI, AS5047, and AS5048A sensors, as well as sensorless operation. Interfaces including USB, CAN, UART, SPI, and IIC provide extensive integration and system customization capabilities.

Technical Specifications

• Model: FSESC 75200 Pro V2.0 with Alu. PCB
• Type: Electronic Speed ​​Controller (ESC)
• Platform: VESC
• Firmware: 6.06
• Firmware updates: Supported
• Operating voltage: 14–84 V
• Battery support: 4–20S
• Continuous current: Up to 200 A at 50 V / up to 150 A at 75 V
• Peak current: 400 A
• BEC: 5 V / 1 A
• Processor: STM32F405 Cortex-M4
• Processor frequency: 168 MHz
• DSP: Supported
• Maximum ERPM: 150,000
• Motor control modes: BLDC, FOC (sinusoidal)
• Control modes: Current, Duty Cycle, Speed, PID
• Sensors: ABI, HALL, AS5047, AS5048A
• Sensorless mode: Supported
• Input signal sources: PPM, ADC, NRF, UART
• Communication interfaces: USB, CAN, UART, SPI, IIC
• Bluetooth: Built-in
• Programming via VESC Tool: Yes
• Phase Filter: Yes
• Regenerative braking: Supported
• Motor/power cables: 8 AWG
• Power button: 16 mm, latching, with red backlight
• Dimensions: 130 × 67.7 × 39.4 mm (with enclosure)
• PCB: Aluminum

Interfaces and connectors

The controller is equipped with connectors for connection and configuration:

• POWER SWITCH - Power button connection
• HALL - Hall sensor and temperature sensor connection
• PPM - Control signal input
• CAN + POWER - CAN bus and power
• USB - PC connection and VESC Tool usage
• COMM - Communication port with ADC, UART/IIC, and power lines
• Motor - Brushless motor connection
• Battery - Battery connection

Communication between the Master ESC and Slave ESC is supported via CAN, enabling use in multi-controller systems.

Wiring diagram:

Protection Systems

The Flipsky FSESC 75200 Pro V2.0 supports configurable protection systems:

• low-voltage protection;
• high-voltage protection;
• overcurrent protection;
• MOSFET overheat protection;
• motor overheat protection.

Protection parameters can be adjusted according to the system configuration.

Advantages

• High Power – continuous current up to 200 A and peak current up to 400 A.
• Wide Voltage Range – supports 14–84 V systems and 4–20S battery packs.
• FOC Control – ensures smooth sinusoidal control of a compatible motor.
• VESC Tool – extensive capabilities

and ESC parameter programming and configuration.

Built-in Bluetooth – wireless configuration and data reading.

CAN bus – enables data exchange and multi-controller system operation.

Sensor support – HALL, ABI, AS5047, and AS5048A.

Sensorless – capable of operating without rotor position sensors.

Regeneration – supports regenerative braking.

Aluminum PCB – improved heat dissipation.

Comprehensive protection – voltage, current, and temperature monitoring.